About Me

5 Laws That'll Help The Fiat Panda Key Fob Replacement Industry
Reasons Your Fiat 500 Key Fob Won't Work

A key fob from Fiat 500 is a convenient method to unlock the doors and get started the car. However, there are many reasons why the key fob might stop functioning. These include a dead battery damaged receiver module, water damage issues, or interference.

This listing is for an NEW replacement Fiat Flip Key Remote that appears similar to the Ilco brand. It has to be professionally programmed (click here to find local locksmiths for your vehicle). It comes with lock, unlock and trunk buttons.

fiat key cover is the most frequent cause of your 500 key fob that isn't working. Modern key fobs come with a limited operating range and must be within only a few feet from the vehicle to function. If you are far from your vehicle, and you press the keyfob button it will not respond, and display the message "Key Fob Not Detected".

If this occurs If this happens, replace the battery in the coin-cell (Part Number CR2032) by a new one from a reputable brand like Panasonic Duracell or Energizer. You can typically find them at your local hardware store or online.

You can test the battery in the coin-cell by pressing the buttons while standing close to your Fiat 500. The car will flash its parking lights and the key fob should operate the lock and unlock switches.

If your key fob still doesn't work even after replacing the battery, it may be water damage which hinders it from communicating with the module in your vehicle. Water damage can occur in a variety of ways, such as an easy splash or submerging the key fob into saltwater at the beach. If you suspect your fob has been exposed to water, try putting it in a dry rice bag to draw the moisture back out. If that doesn't work your fob may need to be reprogrammed by an experienced auto locksmith or by the dealer.

Water Damage

Water damage can occur if you submerge the fob in the ocean, or wash it in a washing machine. Saltwater is especially dangerous to the fob's circuit board, causing it to short out and eventually end up dying. It's not a good thing to get the fob wet, but don't give it up in the event that you accidentally drop it in the water or don't remove it from your pocket.

First take the battery off the fob. Clean the electronic chip using isopropyl or a similar product and then dry it completely before replacing the battery. Check the fob again to verify if it's functioning. If the key still doesn't work, it might need to be changed. This is usually handled by a professional or dealer auto locksmith.

If the key is older and was not programmed to your car, it will likely need to be replaced completely. A professional automotive locksmith can carry out this simple task. The locksmith will need to cut the key to match the ignition of your vehicle. The locksmith also needs to reprogram your fob into the vehicle's system. This is a quick and inexpensive process that can usually be completed within the same day.

Receiver Module Issues

The 500 key fob you have may be inoperable because it's out of range. The remote has a maximum range of 30 feet. So in the event that you are far from your car, it won't respond to your commands. It is possible to fix this by moving the remote closer to your car until it responds.

If you've replaced the battery on your coin (commonly called"button" or "button" or "watch") and your fob still won't work it could be due to an internal circuit board problem. In most cases, reprogramming the fob will solve the problem. There are instructions on how to do this for most automobiles by searching YouTube or checking out the owner's manual.

It is possible to replace the metal clips that hold the coin batteries in the correct position. If they loose tension, it could prevent your coin battery from being properly seated, causing your remote to malfunction.

In rare instances, the fob can become out of connection with your vehicle as a result due to hardware or software issues. This could be a huge issue, but you are able to frequently fix this issue by visiting an auto locksmith to have them reprogram your fob. In certain instances the software might require reinstallation to your body control modules.

Interference

In addition to a dead coin battery, the key fob may not be able to transmit or receive an signal due to interference. This could occur if the key fob is located near an electronic radio transmitter (cell phones and radar detectors) or any other source of electromagnetic radiation. The key fob may not function due to a bad connection to the buttons water damage or damage to the internal chips.

If your key fob suddenly stopped working, or you've tried everything at home to fix it (e.g. You could have a malfunctioning 500 receiver module in the event that you've tried replacing the battery, reprogramming, or using an alternative key fob. The receiver module, which is located beneath the dashboard, detects radio frequency signals from your key fob. It then converts them into electronic commands that the vehicle interprets.

Fortunately, there's an easy method of resetting every single system on board in your 500 device, including the key fob. Disconnect the battery of 12 volts for approximately 15 minutes by removing the negative cable and then the positive cable. Then, reconnect the battery. This will clear any residual electrical charge, and then restart the computer of your car. This could help you get your key fob to work again. If the issue persists, you should seek the advice of an expert technician. They will be able to determine the exact cause of any problems.